CURT 56189 Индивидуальный 4-контактный жгут проводов для прицепа со стороны автомобиля, подходит для некоторых моделей Mitsubishi Outlander, черный

Brand:CURT

3.4/5

94.91

Если ваш автомобиль не оборудован проводкой для буксировки прицепа, заказная проводка CURT — идеальное решение. Специальный жгут проводов, также называемый Т-образным соединителем, представляет собой простое электрическое устройство с функцией plug-and-play, которое подключается к автомобильной электрической системе и обеспечивает стандартное универсальное подключение проводки прицепа. Это делается с помощью двух или более OEM-совместимых разъемов для конкретного автомобиля, которые подключаются к узлу заднего фонаря, что устраняет необходимость резки, сращивания и пайки во время установки. Индивидуальные жгуты проводов изготавливаются для конкретных автомобилей, и, хотя они доступны не для всех автомобилей, они предлагают один из самых быстрых, простых и безопасных способов подключения автомобиля для буксировки. Этот конкретный жгут проводов оснащен 4-контактным плоским разъемом и предназначен для использования в качестве специального жгута проводов, подходящего для Mitsubishi Outlander определенных годов выпуска (чтобы проверить совместимость с вашим автомобилем, см. информацию о приложении). Он поставляется со всеми необходимыми компонентами проводки для обеспечения надежного соединения проводки прицепа, а также с пылезащитной крышкой для поддержания разъема в чистоте, когда он не используется. Вы представляете свой следующий пункт назначения — может быть, это лодка, причалившая к вашему любимому месту рыбалки, может быть, это кемпинг с видом на один из шедевров природы, или, может быть, это следующая крупная стройплощадка. Однако, чтобы превратить эту картину в реальность, нужно больше, чем просто мечтать. Требуется надежное соединение и нужное количество энергии. Индивидуальная проводка CURT изготовлена ​​с использованием одной из самых сложных технологий в отрасли и предназначена для простой установки, обеспечивая долговечное электрическое соединение для вашей установки тягово-сцепного устройства.

СУПЕРОБЛОЖКА. Для обеспечения длительного использования и устойчивости к атмосферным воздействиям этот 4-контактный жгут проводов освещения прицепа поставляется с резиновым пылезащитным чехлом. Когда он не используется, он легко устанавливается на 4-контактный плоский разъем, защищая его от внешних воздействий. НАДЕЖНАЯ МОЩНОСТЬ. Этот 4-жильный жгут проводов прицепа изготовлен с использованием технологии поверхностного монтажа. Этот тип схемы генерирует меньше тепла, оптимальную интенсивность света и долговечность. ДЛЯ КОНКРЕТНЫХ АВТОМОБИЛЕЙ. Этот жгут проводов для вторичного рынка предназначен для автомобилей Mitsubishi Outlander некоторых лет. СТАНДАРТНЫЙ РАЗЪЕМ. Эта вставная 4-плоская проводка прицепа может использоваться для подключения задних фонарей прицепа, стоп-сигналов и сигналов поворота. 4-сторонняя проводка фонарей прицепа популярна на различных прицепах, добавляя универсальные возможности буксировки для вашего автомобиля. ЛЕГКО УСТАНОВИТЬ. Никакой резки! Никакого сращивания! Этот комплект жгута проводов прицепа подключается к существующей заводской проводке вашего автомобиля и оснащен стандартным задним 4-контактным разъемом проводки прицепа для подключения и буксировки прицепа.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.3 4.3 out of 5 stars 118 ratings 4.3 out of 5 stars
Exterior ‎Painted
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 9 x 6 x 3 inches
Item model number ‎56189
Item Weight ‎1.4 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎56189
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎56189
Product Dimensions ‎9 x 6 x 3 inches

3.4

13 Review
5 Star
69
4 Star
13
3 Star
7
2 Star
3
1 Star
7

Напишите свой отзыв

Ваш адрес электронной почты не будет опубликован. Все обязательные поля помечены*

Scritto da: ABC
Working just fine.
For whatever reason, the original wiring harness for my trailer lights failed. I ordered this one to fit my car and I now have trailer lights again. Since I didn't have a place to work on the car, I had our local U-Haul install the wiring harness.
Scritto da: DOBY DADDY
not plug and play
I thought this is supposed to be plug and play. The power wire is not plug and play and needs to be ran under the carpet along the edge so door sill panels and center column lower trim panel need to be taken off. I didn't go through the firewall. I just plugged it into the fuse box under the dash. Also had to drill a hole in the rear floor pan above the spare tire so the spare tire had to be dropped. Whole thing took about an hour.
Scritto da: Rev DoPray
2018 Mitsubishi Outlander Phev Successful Install
I was able to install this into my 2018 Mitsubishi Outlander PHEV GT S-AWC. Everything was hooked up in the back without needing to run the wire under the car to the battery. I just hooked it up to the battery in the back. There also wasn’t a need for any trim/panel removal tools. The instructions were useless but I simply looked at the wiring diagram and installed it. Although I haven’t tested it with my trailer I am giving this product 5-Stars. If I run into difficulty with it functioning correctly I will update my review.
Scritto da: Asher04
Not for Vehicle that already has Factory Tow Package
Before you buy this product - check to see if your vehicle has the factory tow package included. To find out if you do, check the installation video from etrailer (for their product) and the installer will point out in the hood what you need to look for. If you do have the factory tow package go with the model #56296 (ignore the vehicle fit from Amazon: it will say it will not fit your vehicle). Only go with this product if you don't have the factory tow package. I didn't realize I had the factory tow package until I went through the installation steps.
Scritto da: Jana M. Kleffman
Worked Great
Did what it said it was gonna do. Took about 30 minutes to install, nothing complex. Make sure you have the ability to lift your vehicle because you are going to need to crawl along the ground a bit to get the wire up to the front of the vehicle. Not a big issue with ramps. Overall, good kit.
Scritto da: Jason Brinckmann
Watch my video for Installation!!!!
The media could not be loaded. Everything you need and not too terrible to install yourself! Watch my detailed video for a complete overview on the installation because the instructions page that it comes with (-1 star) has incomplete written directions and the photos only show the panel removing in the trunk.
Scritto da: Moises Pimentel
To connect it’s on the driver side left side thank you
It fits perfectly on the video it shows on the right side of the rear end of the 2018 outlander but on the outlander it will be on the left rear of the light fixture the only thing that was different but it works perfectly fine thank you
Scritto da: TLB
Works great
Works great on my three row 2019 Mitsubishi Outlander. Easy to setup even though I had to crawl under my car to run the wire to the engine bay. Electrical tape helps keep the connectors attached to the wires.
Scritto da: Martin Thomas
Good quality and very nice custom fit
Easily plugs into lighting system for a professional installation.
Scritto da: John
No wires to splice
2015 outlander . Easy plug-ins. No cut wires , so if electrical problems come up later you can unplug harness and start trouble shoot the vehicle only . - Routing wire too frount of vehicle can be done with no drilling but a little of a challenge if you are not a young man ????
Scritto da: Amazon Customer
Easy install and working fine
I purchased and installed myself following instructions from YouTube. It's working great.
Scritto da: Gary wilkinson
Excellent and on time
Scritto da: Jim B.
Good for a 2019 Mitsubishi outlander phev
Used this on a 2019 Mitsubishi outlander phev worked great.

Сопутствующие товары

Откройте для себя нашу международную сеть

Мы отправляем в 28 стран, более 200 000 товаров. Будьте в курсе, подпишитесь на рассылку.

Array