Frigidaire 137032600 Тепловой ограничитель Frigidare

Brand:FRIGIDAIRE

3.6/5

69.12

ОПИСАНИЕ ПРОДУКТА Вы когда-нибудь беспокоились о том, что ваша одежда может загореться в сушилке и сжечь весь дом? Возможно, так и должно быть, если вам нужен новый термоограничитель. Этот термоограничитель Frigidaire поможет вам убедиться, что ваша одежда будет теплой и сухой, но не горящей. Эта деталь для ремонта бытовой техники совместима с различными моделями сушилок. Будучи оригинальной запасной частью Frigidaire, этот нагревательный элемент поможет вашему прибору работать без сбоев и идеально справляться со стиркой. ОТ ПРОИЗВОДИТЕЛЯ Это оригинальная сменная деталь. Номер модели и название следующего элемента: Frigidaire 137032600 Thermal Limiter

УСТАНОВКА: Следуйте инструкциям по установке, чтобы обеспечить правильную установку и функционирование этой детали прибора. СОВМЕСТИМОСТЬ: Перед покупкой убедитесь, что запасная часть совместима с вашим бытовым прибором. АРТИКУЛ №: 137032600. ОРИГИНАЛЬНАЯ ЗАМЕНА ДЕТАЛИ: Специально разработана для совместимости с различными сушильными машинами. РЕКОМЕНДУЕМОЕ ПРИМЕНЕНИЕ: Сменный термоограничитель для сушилок для одежды.
Batteries Included? ‎No
Batteries Required? ‎No
Country of Origin ‎China
Customer Reviews 4.5 4.5 out of 5 stars 262 ratings 4.5 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer ‎No
Item model number ‎137032600
Item Package Quantity ‎1
Item Weight ‎1 pounds
Manufacturer ‎Frigidaire
Part Number ‎137032600
Product Dimensions ‎1.5 x 2.5 x 3.5 inches

3.6

10 Review
5 Star
76
4 Star
11
3 Star
6
2 Star
3
1 Star
4

Напишите свой отзыв

Ваш адрес электронной почты не будет опубликован. Все обязательные поля помечены*

Scritto da: JoeO
Exact Fit! Works Great!
My Frigidaire dryer FFLG3911QW1 decided it was not going to dry anymore. The drum would spin, but the burner would not light. After watching a few YouTube videos I decided to tackle this project on my own. Dryer was easy to come apart and once inside I found years of lint (some of it looked burnt!) There are a number of sensors to check. Use your multimeter to check for continuity. If this part is bad it will show OPEN (no continuity) Installed the new part.. closed up the dryer and BAM... works great! Total time for the job 45min to disassemble, diagnose and clean the lint out 60min to install, reassemble and test (had some trouble getting the door back on the dryer) If you can DIY this repair, you would save $200+
Scritto da: Sharon
Frigidaire?
I'm not sure if this part is genuine Frigidaire. It did not come in a typical Frigidaire packaging and the stamping on the part is inconsistent with similar Frigidaire parts. On the bright side, shipping only took one day, and the part works. My wife is happy the dryer is working again. I try to purchase genuine OEM parts. If a part is a knockoff it should be stated in the description.
Scritto da: Eileen K
My fiance has some electrical experience and replaced both parts fairly easily. It took him approximately 2 hours
I started getting the dreaded error message E64 on my Frigidare Affinity Dryer. My dryer would still heat up but about half way through the cycle would quit. You could restart it and it would go halfway through the cycle and quit again. I googled the area and first found that it could be the heating coils but that didn't make much since as I didn't think it would heat up so effectively if that was the case. I did more research and found that it could be the thermostat and the heat safety part Frigidaire 3204267 Safety Thermostat for Dryer. My fiance has some electrical experience and replaced both parts fairly easily. It took him approximately 2 hours. He followed directions that were easily found. I highly recommend going this route first if you have a little bit of fix it skills. Costs a lot less than a service call. The coils aren't difficult to get at if it turns out to be the problem.
Scritto da: Lar
It works great!
Once we got to it, it was simple to change. It saved us a repair bill!
Scritto da: Six am
Broke the old one getting the wires off of it. Glad I had already orded a replacement even though probably didn't need for E64.
I bought this because I was getting the error code e64 on my Electrolux dryer but I don't know for sure if this was the problem because I replaced the heater coil assembly and another thermostat but I figured while I had it apart it would be better to replace all parts rather than putting It back together only to find out I hadn't fixed it. Anyways I ended up breaking one of the tabs that the wires attach to when taking the wires off the old one pictured. If I had not had the replacement part I would have been waiting for one of these to put it back together. I would recommend this along with the heater replacement just in case. It's worth the extra money spent IMHO. Easy fix overall. Pictures show the coils glowing on the back of the dryer after replacing this part and the heating coils.
Scritto da: Leah Blizard
Original part
Said it was a Electrolux part . Looked just like original on heating coil housing. Fit the same and worked. Time will tell on how long it last. Original lasted 10 years.
Scritto da: Scott D Coyle
This part only lasted a month. Not a quality part that I overpaid for.
This part only lasted a month. Not a quality part that I overpaid for.
Scritto da: Josh Frazetta
Cheaper than replacing the dryer
Work prefer replacement for our dryer Frigidaire affinity FASE7073NW0 no issues after 11 months.
Scritto da: Rick F.
ORIGINAL SUBSTITUTE PART - FITS + WORKS LIKE ORIGINAL
Not much to say. This is the exact same original part as what was originally installed in my dryer. Works great. I will add a short comment - This specific part is actually a one time heat fuse. Once it blows, that's it, it needs to be replaced. This is unlike the other similar part next to it in my dryer which resets itself once it has a chance to cool down again. So,,, DO NOT TEST THIS DEVICE WITH HEAT (like a cigarette lighter or heat gun etc) to make sure it's working correctly as some posts on the internet tell you. If you do try to test this device with heat, you will end up needing to buy a new one. That's why I had to buy this replacement for the original one in my dryer.
Scritto da: Tony
Got it fast
Came in 2 days, was the right part and works great. dryer is drying cloths again

Сопутствующие товары

Откройте для себя нашу международную сеть

Мы отправляем в 28 стран, более 200 000 товаров. Будьте в курсе, подпишитесь на рассылку.

Array