MG Chemicals 8349TFM Теплопроводный эпоксидный клей 1 к 1, двухкомпонентный двойной шприц объемом 25 мл

Brand:MG Chemicals

2.6/5

75.51

Обеспечивает сильную электрическую изоляцию. Время отверждения: 16 часов при комнатной температуре или 20 минут при 65 °C (149 °F). Соотношение смешивания 1:1. Срок годности: 20 минут. Огнестойкий – соответствует UL 94V-0. Теплопроводность 1,1 Вт/(м·К).

Обеспечивает сильную электрическую изоляцию. Время отверждения: 16 часов при комнатной температуре или 20 минут при 65 °C (149 °F). Соотношение смешивания 1:1. Срок годности: 20 минут. Огнестойкий – соответствует UL 94V-0. Теплопроводность 1,1 Вт/(м·К).
Brand MG Chemicals
Compatible Material Glass, Ceramic
Item Form Liquid
Item model number 8349TFM-25ML
Manufacturer MG Chemicals
Material Epoxy Resin
Product Dimensions 3.02 x 8.06 x 2.02 inches; 1.59 Ounces
Special Feature Strong

2.6

7 Review
5 Star
47
4 Star
13
3 Star
6
2 Star
17
1 Star
17

Напишите свой отзыв

Ваш адрес электронной почты не будет опубликован. Все обязательные поля помечены*

Scritto da: James smith
It sticks, compared to the many others I have tried. Make sure you mix the compound!
Mostly likes, It is kind of hard to squeeze the product out. If you can't get the conductive compound out Take a small instrament and open the pathway to get it started. It works. Don't give up!
Scritto da: JS
Part B stays in the syringe
When first opened, Part B would not come out, while Part A was squirting. First tried only pushing on the Side B part of the plunger. Finally had to insert a toothpick into Part B and stir it some, then a little would come out. I only needed a small amount, so when I can get a little of Part B out (some just from the toothpick), I take an equal amount of Part A from the Part A puddle. If I needed a larger volume of epoxy, it would have been unsuccessful. The epoxy does cure into a tough solid, and it seems to be adhering to both metal wire and the plastic wire sheathing.
Scritto da: David Carlson
Good epoxy!
This epoxy worked well for our applications. Not sure why the negative reviews.
Scritto da: Nathan Bonsal
Best used in very thin layer
Thermal conductivity about 3x what JB Weld is, not as good as thermal grease, but it adheres and grease will not. Spread it VERY thin, and clamp. Shipped fast, dispenser is of high quality.
Scritto da: Ning G.
Hard to get refund
I totally ordered two adhesives and opened one. The component in one syringe dried and was not able to pushed out. I returned two and got a refund for all first but was charged again for one later.
Scritto da: Charles Faris
Hardener partially cured on receipt
The product arrived as scheduled but when dispensed, the resin flowed nice. However the hardener didn't flow at all. After dispensing it by cutting through the body of the tube, it DID perform well.
Scritto da: Scott Quartochi
Worthless!
One of the parts was solid and unusable. Will never buy this again.

Сопутствующие товары

Откройте для себя нашу международную сеть

Мы отправляем в 28 стран, более 200 000 товаров. Будьте в курсе, подпишитесь на рассылку.

Array