Регулятор объема воздуха серии F93 Penn для глубоких колодцев, открывается при перепаде давления, без манометрического крана, без клапана сброса давления F93A-1C

Brand:Johnson Controls

3.7/5

129.89

Регуляторы объема воздуха серии F93 для глубоких колодцев контролируют количество воздуха в бытовых резервуарах для хранения воды систем водоснабжения из глубоких колодцев. Глубокие колодцы имеют глубину более 25 футов (7,6 м). Контроллеры серии F93 автоматически поддерживают объем воздуха в накопительных резервуарах систем глубокой скважинной воды, позволяя воздуху выходить из резервуара в окружающее помещение, когда уровень воды в резервуаре падает (увеличение объема воздуха). Глубокий колодец F93 управляет открытием воздушного клапана при падении уровня воды в резервуаре и выпуском избыточного воздуха из резервуара при давлении до 100 фунтов на кв. дюйм (690 кПа). Модель F93H оснащена клапаном сброса минимального давления, чтобы избежать снижения давления в баке ниже 25 фунтов на кв. дюйм (172 кПа). Используйте эту модель в приложениях, где возможен быстрый слив воды. Обратитесь к Бюллетеню по продуктам для регуляторов объема воздуха серии F93 для глубоких колодцев (арт. № 24-7664-3000) для получения важной информации о применении продукта.

прочный корпус из норилового сплава (высококачественный термопласт), устойчивый к механическим повреждениям и коррозии.
Country of Origin USA
Item model number F93A-1C
Manufacturer Johnson Controls, Inc
Package Dimensions 10.2 x 3.94 x 1.73 inches; 7.05 Ounces

3.7

8 Review
5 Star
79
4 Star
12
3 Star
4
2 Star
2
1 Star
3

Напишите свой отзыв

Ваш адрес электронной почты не будет опубликован. Все обязательные поля помечены*

Scritto da: JS
Water tank switch
Fit great no issues
Scritto da: Beaty Wade Tharp
Fine valve
This style of valve is just fine for its function. My only wish is some ingenious engineer would figure out a way for the air vent portion of the valve to not get plugged up. I.e. some sort of wiper assembly that cleans off the air vent port as the float cycles up/down.
Scritto da: JERED ECKLE
Works like a champ!
Replaced one just like it in style. Immediately started working like it should after a few drain & fills of the tank!
Scritto da: MnBoy
It works.
Turned power off to deep well. Drained the water from the existing metal water tank through faucets. Waited until all the water... then air... left the tank. Closed the faucets. Took the old volume control out and put the new one in. This was a fairly easy procedure. Turned power on and waited for tank to fill. I could hear the air escaping the valve, which I did not hear on the old valve. The tank filled properly and I turned the faucets on to bleed air from lines. Pump runs only a fraction of what it did prior to new valve installation. I think the price is a bit high, but if it helps the pump by running less it is probably worth it.
Scritto da: Patrick
Identical to original.
Works fine but the arms on these floats are not a solid rod and that is what went bad on my old one. The arm bend up . These look identical to my original so i decided to beef up the rod with a piece of 8 awg solid copper wire soldered to the float arm. If not for the weak float arm this device would probably never fail.
Scritto da: Quail Valley Farm
Can't go wrong with Johnson Controls components
This switch closes the air pressure relief valve when the water level in the tank reaches the appropriate level. The switch was failing and dripping water in the pump house, non-stop. This is the exact same brand/model I replaced, and the one that failed was on the tank when I purchased the property in 2003, demonstrating its longevity. Given this is a farm tank, serving a home with a pool, and the property, it gets a significant workout. I suspect that because the well is inside of a structure, this switch and other components last somewhat longer than they would if the well system was exposed to the elements.
Scritto da: Mark Williamson
Says Penn, not Johnson controls.
Using it as a spare, not installed yet.
Scritto da: Roark
Works very well and has “secret” ability. :)
Perfect replacement for my deep-well system. Something not mentioned in the description is this has an *optional* outlet for gauge/pressure switch that is pre-threaded. If you dont need this feature, simply do nothing. This threaded recess does NOT by default connect to the tank-side pressure. If you want this feature, simply drill a small (tiny is fine!) hole in the threaded recess and screw your gauge or pressure switch in. That little hole connects the gauge to the pressure side of things. This means one unit can fill the role of two. Simply drill the hole to allow connection of a pressure switch or gauge. Neat!

Сопутствующие товары

hot

Откройте для себя нашу международную сеть

Мы отправляем в 28 стран, более 200 000 товаров. Будьте в курсе, подпишитесь на рассылку.

Array