Urbt America 2-1/2 karbīda urbuma zāģis/griezējs ar 1 griezuma dziļumu, CTH Series 1 griešanas dziļums 2-1/2

Name: Urbt America 2-1/2 karbīda urbuma zāģis/griezējs ar 1 griezuma dziļumu, CTH Series 1 griešanas dziļums 2-1/2
Brand: Drill America
SKU: 0887861226301
Price: 118.67 EUR
Availability: InStock

Brand:Drill America

3.7/5

€
118.67

Drill America CTH karbīda caurumu griezēji piedāvā vienkāršu un efektīvu veidu, kā urbt lielāka diametra caurumus, neprasot lielus urbjus un īpaši lielus patronas. Tie ir izgatavoti no augstākās kvalitātes ātrgaitas tērauda ar karbīda uzgaļiem, kas nodrošina īpaši ilgu kalpošanas laiku. Caurumu griezēji no karbīda ar urbumu griezējiem griež dažādus materiālus, piemēram, nerūsējošo tēraudu, čugunu, dzelzi, lokšņu metālu un varu. Tie labi darbojas arī ar abrazīviem materiāliem, piemēram, augsta blīvuma sveķiem un metāla plāksnēm. Caurumu griezējam ir 1/2 kāts, un tas ir aprīkots ar piloturbi un sešstūra atslēgu.

Summa

Pievienot grozam Pērc tagad

EAN: 0887861226301

Kategorijas instrumenti un mājokļa labiekārtošana, Elektroinstrumenti un rokas darbarīki, Elektroinstrumentu daļas un piederumi, Elektrourbju daļas un piederumi, Durvju zāģi un piederumi, Durvju zāģi,

Komplektā ar piloturbi, sešstūra atslēgu un automātisko izstumšanu. 1/2 kāts, 1' griezuma dziļums. Izgrieziet dažādus materiālus, piemēram, nerūsējošo tēraudu, čugunu, dzelzi, lokšņu metālu un varu. Labi darbojas ar abrazīviem materiāliem, piemēram, augsta blīvuma sveķiem un metāla plāksnēm. Vienkāršs un efektīvs veids, kā urbt lielāka diametra urbumus, neprasot lielus urbjus un īpaši lielus patronas. 2-1/2 diametrs ar 1 griezuma dziļumu.

Brand	Drill America
Cutting Diameter	2-1/2" Inches
Finish Type	Uncoated
Is Discontinued By Manufacturer	No
Item model number	CTH2500
Manufacturer	Drill America
Material	Carbide-Tipped
Product Dimensions	6 x 4 x 4 inches; 15.87 Ounces
Shank Type	Hex

5 Star

4 Star

3 Star

2 Star

1 Star

Uzrakstiet savu atsauksmi

Jūsu e-pasts netiks publicēts. Visi obligātie lauki ir atzīmēti ar^*

Jūsu vērtējums

Scritto da: Daryl B.

Excellent cutter!

This cutter gave a very smooth cut in 1/8" aluminum panel for my project! This is a large diameter size, so be cautious of the speed. My drill press was slowed to 700 rpm's. VERY PLEACED WITH THIS PRODUCT. Thanks, from Indianapolis.

Scritto da: caihu lemon

Cut quality

From now on this is the only brand I will use for hardened drill bits drilled 3/16 of 304ss

Scritto da: J W

Works great if used properly

Bought this for working with heavy steel, I have cut 3 holes through 1' mild steel and as many through 1/2'. It took some tuning to get the drill press dialed in, but at the proper speed and with some lubricant it does a nice job. On pieces thicker than 1/2 it works best to flip the metal over halfway through the cut to finish from the other side. Looks pretty much new after the 6 holes I've used it for, looking forward to using it on the next job.

Scritto da: shabbyjude

Best Cutter, but BEWARE

This is by far the best hole saw I have ever had over the last 50 yrs....the only negative is the quality control...after drilling 1 [ONE!!!!] hole, the set screw fell out...at least the screw had the courtesy to wait until the drill press stopped....so beware to check the set screws before using....I drilled a small relieve on the shaft so the set screw would not just be sitting on a flat area....then max lock tight on both screws....drilled 10+ more holes with 0 [ZERO] problems...that's why it gets a 5 star rating, unlike other hole saws with carbide tips that only manage to get thru a few uses...I am cutting thru 3/8'' plate steel and couldn't be happier....

Scritto da: APO

Heavy duty

The casing is 1/8" thick, 1" depth and heavy duty. Not like the other brand which casing is 1/16 thick. The picture shows shallow depth however it' 1" deep, compatible with Japanese product selling on MSC @ a higher price

Scritto da: Rich Bessom

Use at low RPMs with plenty of cutting oil.

I was very pleased with the operation of the 2-5/16" carbide tipped hole saw! I had to make 4 holes for the marker side lights on my vintage race car trailer that I'm rebuilding. I used it in an old 1/2" craftsmen hand drill motor. All the holes drilled very smoothly. The pilot drill worked great & didn't let the saw wander. The metal was 14 gauge steel, roughly a little thicker then a 1/16". The hole saw still looks brand new. It was shipped in a plastic protective container along with the Allan wrench for the pilot drill. It was well worth the money! I would recommend this tool! Thanks!

Scritto da: Jerry Sikes

Cut through body steel like a hot knife through butter

Following proper use recommendations to use cutting fluid to cool the tool and operating at a slow speed the tool surpassed all o my expectations and smoothly cut a clean precise hole even using it in a hand held drill. It is the best hole cutting bit I have ever used. I highly recommend this tool and have already purchased additional sizes. I am not a professional in a machine shop I use this at home.

Scritto da: PDGx

Fast and aggressive drill

Very aggressive hole saw/drill. Used on structural channel iron to pass 3.5” pipe through (3.5” drill size). Final hole does appear to be about a 64th small, but that is easy to correct. Just keep it lubed with cutting fluid.

Scritto da: Grant

Quality Product!

We use this product daily to add extra ventilation in our shipping containers. Quality product!

Scritto da: Sparkbing

Drill bit is garbage

Drill bit broke within seconds Can replace it nor does the seller have replacement bits

Scritto da: Becky Erickson

Five Stars

Good product.