VEVOR gaisa spilvena domkrats, 3 tonnu trīskāršs gaisa spilvena domkrats, gaisa spilvena domkrats līdz 15,75 collu pacelšanai, 3-5S ātri paceļams gaisa spilvena domkrats automašīnām ar īsu rokturi (bēšs) 3 tonnu īss rokturis

Brand:VEVOR

3.5/5

269.40

Plašs pielietojums: ātrā domkrata automašīnas pacēlājs ir lieliski piemērots situācijām, kad ir nepieciešams pacelt vienu riteni mīkstā reljefā, ūdenī uz smiltīm vai dubļainiem ceļiem ģimenes automašīnām, miniveniem, apvidus auto un bezceļa transportlīdzekļiem. Vietu taupošs dizains: pārnēsāšanas roktura dizains atbilst rokas formai, lai jūs varētu pilnībā kontrolēt domkratu, kad to izmantojat. Un visa struktūra ir kompakta un viegli uzglabājama. Tātad jūs varat to ērti ņemt ārā. Droša lietošana: vispirms turiet sarkano vārstu aizvērtu, atveriet zaļo vārstu un ievadiet saspiesto gaisu; piepūšot līdz augstumam, izslēdziet zaļo vārstu. Pēc lietošanas atveriet sarkano vārstu, lai izvadītu gaisu. Drošības vārsts vidū nodrošina, ka ievadītā gāze nav pārmērīga, lai nodrošinātu lietošanas procesa drošību. Lieljaudas konstrukcija: mūsu pneimatiskais domkrats ir izgatavots no augstas stiprības tērauda, ​​kas padara visu ķermeni izturīgu un izturīgu. Pulverkrāsas tērauda rāmis un gumija sakrīt, lai samazinātu triecienu. Augsti noslēgtie gaisa spilveni neiztecēs un nesaskrāpēs. Lielāka noslogotā vieta iederas mīkstā un viegli saliekamā vietā. Darbu taupošs domkrats: Pneimatiskā domkrata ietilpība: 6600 mārciņas/3T. Minimālais augstums: 5,3/135 mm. Maksimālais augstums: 15,75/400 mm. Pacelšanai nepieciešamas tikai 5 sekundes. Darba temperatūra: -60 ℃ ~ 50 ℃. Gaisa ieplūde: G1/4. Mūsu trīskāršās somas domkrats ir vienkāršākais un ātrākais veids, kā pacelt automašīnu.

Nav pieejama neviena vienība
Plašs pielietojums: ātrā domkrata automašīnas pacēlājs ir lieliski piemērots situācijām, kad ir nepieciešams pacelt vienu riteni mīkstā reljefā, ūdenī uz smiltīm vai dubļainiem ceļiem ģimenes automašīnām, miniveniem, apvidus auto un bezceļa transportlīdzekļiem. Vietu taupošs dizains: pārnēsāšanas roktura dizains atbilst rokas formai, lai jūs varētu pilnībā kontrolēt domkratu, kad to izmantojat. Un visa struktūra ir kompakta un viegli uzglabājama. Tātad jūs varat to ērti ņemt ārā. Droša lietošana: vispirms turiet sarkano vārstu aizvērtu, atveriet zaļo vārstu un ievadiet saspiesto gaisu; piepūšot līdz augstumam, izslēdziet zaļo vārstu. Pēc lietošanas atveriet sarkano vārstu, lai izvadītu gaisu. Drošības vārsts vidū nodrošina, ka ievadītā gāze nav pārmērīga, lai nodrošinātu lietošanas procesa drošību. Lieljaudas konstrukcija: mūsu pneimatiskais domkrats ir izgatavots no augstas stiprības tērauda, ​​kas padara visu ķermeni izturīgu un izturīgu. Pulverkrāsas tērauda rāmis un gumija sakrīt, lai samazinātu triecienu. Augsti noslēgtie gaisa spilveni neiztecēs un nesaskrāpēs. Lielāka noslogotā vieta iederas mīkstā un viegli saliekamā vietā. Darbu taupošs domkrats: Pneimatiskā domkrata ietilpība: 6600 mārciņas/3T. Minimālais augstums: 5,3/135 mm. Maksimālais augstums: 15,75/400 mm. Pacelšanai nepieciešamas tikai 5 sekundes. Darba temperatūra: -60 ℃ ~ 50 ℃. Gaisa ieplūde: G1/4. Mūsu trīskāršās somas domkrats ir vienkāršākais un ātrākais veids, kā pacelt automašīnu.
Brand VEVOR
Brand ‎VEVOR
Color black
Color ‎black
Country of Origin ‎China
Customer Reviews 4.4 4.4 out of 5 stars 126 ratings 4.4 out of 5 stars
Item model number ‎White Triple Bag Jack
Item Weight ‎19.5 Kilograms
Item Weight ‎42.9 pounds
Load Capacity 3 tons
Load Capacity ‎3 tons
Manufacturer ‎VEVOR
Manufacturer Part Number ‎Long Handle White Air Jack
Material Alloy Steel
Material ‎Alloy Steel
Minimum Height ‎400 Millimeters
Model ‎Triple Bag Car Jack
Package Dimensions ‎20.1 x 16.5 x 7.1 inches
Style ‎Short Handle
Vehicle Service Type Car
Vehicle Service Type ‎Car

3.5

12 Review
5 Star
72
4 Star
11
3 Star
10
2 Star
0
1 Star
6

Uzrakstiet savu atsauksmi

Jūsu e-pasts netiks publicēts. Visi obligātie lauki ir atzīmēti ar*

Scritto da: Richie
It works, it's fast ... but
This air jack does work and it is fast for my needs: a Fiat 500 Pop, a Fiat 500 Abarth and a Nissan Sentra. Both Fiats have lowered suspension and this jack is low enough to get where it needs to go. Having said that, there are no assembly instructions at all. There is a sheet of paper with icons and a short how to use but none for assembly. However, It is not difficult to figure out. You will need a 10mm wrench or socket with an extension and a Phillips head screwdriver to attatch the 6 nuts and bolts for handles and control block (sorry about the oil marks on the instruction sheet, that's from having to use a 6x1.0mm die to fix the thread on one of the bolts!) You will need scissors or cutter and 13mm wrench to attatch the hose on the Control Block as well. The hose supplied is longer than necessary and, in my case, when attatched as is, the hose kinked at one of the bends, shortening the hose removed the kink. My jack was supplied with a 3/8 inch air hose fitting. My compressor and hose uses a 1/4 inch fitting (as do most home DIY). I had to remove the 3/8 inch (male) hose fitting on the control block and install a 1/4 inch fitting.
Scritto da: J Valenzuela
For a car yes but for SUV: NO
I had to revise my review to reveal more in addition regarding poor welding quality perhaps the whole assembly line's aim is just box and ship it. Even the screws were at the cheapest level I couldn't use so I changed them all while I properly apply the right torque. I also wanted to add that in order to take a wheel off a Mazda CX-5 (jacked up from the side) it needs maybe 4" additional. Having said that for the solution of a 4x4 wood block is enough while still embrace the speed of it.
Scritto da: Eric P
Where have you been all my life!
I am happy with this jack. I own a towing company. Having a good jack is crucial. Often on soft ground conventional jacks are impractical. My service truck has on board air so this is a perfect fit.
Scritto da: T. P.
Great tool
This jack is a great addition to my tools in my shop.
Scritto da: CARL KOLBERG
Very easy to use and works great
great product and works great
Scritto da: eneidamaria
Retorque all the Allen screws before using.
The best part about this jack is NOT having to pump the handle or twisting the handle to lower the jack. I lifted the left side of a Ford Explorer (~4,000 lbs) easily with about 60 PSI. Unlike a hydraulic jack, the lift was smooth and quick. Having a tow handle makes positioning the jack a snap. The air line connection is the same as all my air tools. The bronze filter fitting on the exhaust side is a thoughtful idea so the user does not get an air blast when lowering the jack. Being able to slowly control the lowering is a major improvement over my hydraulic floor jacks. I always check torque on the fasteners before using the device. A couple of the 16 screws were less than finger tight. I torqued all of them to 150 inch pounds, 4 and 5 mm Allens. I also cut a 4X4 block to sit over the rubber cap for some extra height. Probably won't use it for my Ford Edge. Overall, very pleased with this device.
Scritto da: P. MCGAFFEY
Works for sports cars.
Getting too old to pump up an old jack, so I thought i would give this thing a try. It worked pretty well and very quickly on my low sports car. I does not like working at angles though. It sticks. After watching a YouTube video, I opened the airbag up to lubricate the steel sleeves inside. I found that they were already coated with lightweight gray grease. I tried it on my SUV to change brake pads. It was a little sketchy to stack up blocks of wood to get the extra height needed to get the wheels off the ground. Had to do it in several steps which wasted a lot of time. Next time, I will just use my standard floor jack for that job.
Scritto da: ron sprugasci
Nice easy to use
No dislike used on my car lift to take tires off
Scritto da: Amazon Customer
Very nice product
Easy to use fast elevation it’s look like a good product, we will see in the future
Scritto da: Super
Super fiabilité
Stabilité et fiabilité j’adore
Scritto da: Amazon Customer
WOW just WOW!!!
got this for my dad as a Father's day gift. it works awesome! My Dad's Sorento 2020, my Chrysler 300S 2016 and my wife Elantra 2019 all went and got tire changes with this with no issue. Yes do keep it as straight as possible, if not it kinda sticks, but it's understandable. Very very happy with the purchase. I did have to put a reg US air inlet on it which i already had.
Scritto da: FDIMIKE
It is a bit wobbly.
Whatever is inside of the air bags used to keep the bags straight inline when raising and lowering is a very loose fit, causing the jack to tip one way or the other as it goes up, even on a concrete floor. It causes the jack to jerk when going up and actually stop altogether when trying to lower.

Saistītie produkti

hot
Hi-Lift Jack LM-100 Lift-Mate
3.8/5

€ 121.04

Hi-Lift Jack LM-100 Lift-Mate
3.8/5

€ 121.04

Atklājiet mūsu starptautisko tīklu

Mēs piegādājam uz 28 valstīm, vairāk nekā 200 000 produktu. Esiet informēts, abonējiet biļetenu.

Array