Anderson Metals - 57001-1616 Латунный фитинг для шланга, соединитель, 1 штуцер x 1 с наружной резьбой, 1 штуцер x 1 с наружной резьбой NPT

Brand:Anderson Metals

3.7/5

38.79

Этот латунный соединитель для компрессионного шланга Anderson Metals имеет охватываемый конец для соединения с трубой с резьбой, соответствующей стандартам Национальной трубной резьбы (NPT), и штуцер с зазубринами для соединения со шлангом. Фитинг с зазубринами на одном конце создает герметичное уплотнение на гибком или полужестком шланге при использовании шлангового хомута, обжимной втулки или наконечника (продается отдельно), а соединитель с наружной резьбой NPT на другом конце соединяется с трубой с резьбой для образования герметичного соединения. , фиксированное соединение Этот фитинг изготовлен из латуни для обеспечения коррозионной стойкости, пластичности при высоких температурах и низкой магнитной проницаемости. Латунь можно соединять с медью, латунью, пластиком, алюминием и сварной сталью, а относительная мягкость латунной резьбы по сравнению с другими металлами обеспечивает герметичное уплотнение для предотвращения утечек. Этот соединитель имеет диапазон температур от -32 до +140 градусов по Фаренгейту и подходит для использования в гидравлических, пневматических и сантехнических устройствах. Anderson Metals производит латунные фитинги, клапаны и патрубки для труб. Компания, основанная в 1951 году, имеет штаб-квартиру в Канзас-Сити, штат Миссури.

Эти фитинги содержат свинец, и в соответствии с федеральным законодательством их установка для использования с питьевой водой в США и на их территориях запрещена. Предназначен для использования с хомутом или наконечником обжимного типа (продается отдельно). Примечание. Пожалуйста, ознакомьтесь с изображением таблицы размеров перед покупкой. Диапазон температур от -32 до +140 градусов по Фаренгейту. Зазубренный хвостовик обеспечивает надежное соединение со шлангом. Относительная мягкость латунной резьбы по сравнению с другими металлами обеспечивает герметичность. Латунь для коррозионной стойкости, пластичности при высоких температурах и низкой магнитной проницаемости.
Brand Anderson Metals
Color Brass
Connector Type Barb and Male Pipe
Country of Origin USA
Domestic Shipping Item can be shipped within U.S.
Exterior Finish Brass
International Shipping This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer No
Item Dimensions LxWxH 3 x 2 x 2 inches
Item model number 57001-1616
Manufacturer Anderson Metals
Material Brass
Number of Pieces 1
Product Dimensions 3 x 2 x 2 inches; 4.66 Ounces
Size 1" Barb x 1" NPT Male
Thread Size 1 inch
Thread Type NPT

3.7

13 Review
5 Star
80
4 Star
11
3 Star
4
2 Star
1
1 Star
4

Напишите свой отзыв

Ваш адрес электронной почты не будет опубликован. Все обязательные поля помечены*

Scritto da: Amazon Customer
good Review
Good Review
Scritto da: J. Stright
1 inch NPT barb connector
Nice brass fitting with exact size measurements
Scritto da: Hybrid_john_33
Does the job
The guys say it works flawlessly underwater while diving. No kinks
Scritto da: gardy constant
That is fit and of good quality
Just what I needed, good quality
Scritto da: Daryl
fitting pipe size fits loose
the 3/4" pipe thread was 100% correct & solid material but the barbed section fits sloppy in 3/4" plastic water line. Wasted money here
Scritto da: John W. Woodhull
Barb diameter too small for black polyethylene irrigation tubing - not a good application
Used this adapter to connect a threaded 3/4" valve to 3/4" black polyethylene irrigation tubing - the ID of the 3/4" tubing is clearly larger then the barbs so seal is very poor and water drips from the fitting. I plan to replace this with a threaded copper fitting to transition to 3/4" copper tubing and then connect that to the irrigation tubing, I think that will work better. The barbs are likely fine for other uses, but not for this.
Scritto da: Keith N
Fix/upgrade your Sears C3 air pump hose
I purchased this to fix my Sears C3 air pump hose and I also purchased a CTA Tools 1930 Straight Lock-On Air Chuck . It fits ~too~ perfectly in the hose. It will need to be hose clamped on or I used cable ties to secure. I wish I did not take a earlier review recommendation on a 3/16 inch and purchased one size larger like the 1/4" male to get more of a snug fit. To connect both brass parts, I used plumbers tape wrapped twice to stop air leaks. Use a cigarette lighter to carefully melt nylon webbing after making the cut to control nylon covering the hose from fraying. Tip: You can pinch the hot melted nylon beads to flatten and making it a even spread. Be Careful.. ..It is HOT and may stick to fingers if is really hot. Tip and Caution! I should also add.. that do NOT pump air if chuck is NOT attached to tire or you can possibly damage your pump because if not attached to your tire, you are compressing air in just the hose giving you pump some serious abuse. After filling air in tire, make sure to release compressed air left in the hose my pressing the metal in the air chuck.
Scritto da: Meowsef 907
Fantastic
The media could not be loaded. Great quality , great price, better than oem part from doorman and half the price.
Scritto da: Torsten
Does not match domestic plumbing standards.
Please beware that the 1 1/4" barb will not fit domestic poly pipe (used for wells, etc). A domestic barb fitting would be 1 1/4" ID. These are 1 1/4" OD. So they are way too loose - like a hot dog in a hallway :) Additionally, the male pipe thread is not a perfect match for NPT. The fit is off a bit - you'll need lots of thread sealant to get a leak-free fit. Overall do not buy unless you need a barb for 1 1/4" ID hose/pipe.
Scritto da: Jarred D
Nope!
Happy to find this on Amazon but….Barb end shorter then I expected which doesn’t give me the confidence for the application. Barb end is too loose like others have mentioned for well water piping. A big no - returned, looks like I will be reusing plastic fitting.
Scritto da: Bianca Jacob
1"barbx3/4"pipe thread.
Perfect fit.one inch barb and 3/4pipe thread.does contain led.not for drinking but other than that.good quality exactly as described.enough thread and plenty of barb to put 2 clamps if needed side by side.tight fit for 1"inner diameter pipe.
Scritto da: Marc Lake
Not as pictured...
The barb was much shorter than shown in illustration. Did not feel there was enough room for two hose clamps so I returned item.
Scritto da: Anthony McQuillan
Good quality and reasonable price
Good quality, reasonable price and fast shipping.

Сопутствующие товары

Откройте для себя нашу международную сеть

Мы отправляем в 28 стран, более 200 000 товаров. Будьте в курсе, подпишитесь на рассылку.

Array