Комплект изоляции водонагревателя Reach Barrier 3016

Name: Комплект изоляции водонагревателя Reach Barrier 3016
Brand: Reach Barrier
SKU: 0785577135255
Price: 103.04 EUR
Availability: InStock

Brand:Reach Barrier

3.3/5

€
103.04

ОПИСАНИЕ ПРОДУКТА Комплект изоляции водонагревателя Reach Barrier 3016. ОТ ПРОИЗВОДИТЕЛЯ Reach Barrier 3016 Single Reflective Air Water Heater Insulation Kit поддерживает температуру воды в баке в течение более длительного периода времени и подходит для большинства размеров баков водонагревателей. Это сэкономит деньги, потому что на нагрев воды может приходиться от 14 до 25 процентов энергии, потребляемой в доме. Добавление изоляции к водонагревателю может снизить потери тепла в режиме ожидания на 25-45 процентов. Любой бак водонагревателя, теплый на ощупь, может выиграть от комплекта изоляции. В комплект изоляции водонагревателя Reach Barrier 3016 с одним отражающим воздухом входит (1) рулон 24 на 192 дюйма защитной пленки Reach Barrier Single Reflective Air™, термостойкая лента и простое руководство по эксплуатации. Светоотражающие изоляционные материалы Reach Barrier являются одними из самых универсальных и энергоэффективных изоляционных материалов. Излучающие (отражающие) барьеры устанавливаются на чердаках, стенах, настилах крыш и перекрытиях. Большинство недавно построенных домов содержат изоляцию из лучистого барьера из-за доказанной эффективности снижения энергопотребления и затрат за счет уменьшения притока тепла летом и потерь тепла зимой. Установка лучистого барьера может быть самым дешевым улучшением, которое может привести к наибольшему общему сокращению потребления энергии и затрат. Single Reflective Air соответствует стандартам ASTM и строительным нормам.

Нет доступных единиц

EAN: 0785577135255

Категории Tools & Home Improvement, Building Supplies, HVAC, Погодозащита, Обшивки для труб,

В комплект входят: 1 защитная пленка водонагревателя с пузырьковой изоляцией Reach Barrier (Tm), которая подходит для большинства размеров резервуаров водонагревателя, термостойкая лента и простое руководство по эксплуатации. Простая в использовании и установке предварительно вырезанная панель не требует защитной одежды или специальных инструментов при установке. Превышает новые нормы пожарной безопасности и не требует обслуживания. Изоляция включает в себя 2 слоя 5/32-дюймового барьерного пузыря, ламинированного между 2 слоями отражающего полиэтилена, что поможет обеспечить более стабильные значения R. Отражающая изоляция Reach Barrier (Tm) и технология Bubble Barrier блокируют до 95 процентов лучистого тепла, что помогает экономить энергию и деньги.

Batteries Required?	‎No
Country of Origin	‎China
Customer Reviews	4.3 4.3 out of 5 stars 177 ratings 4.3 out of 5 stars
Item model number	‎3016
Item Package Quantity	‎1
Item Weight	‎2.2 pounds
Manufacturer	‎Reach Barrier
Part Number	‎3016
Power Source	‎Corded electric
Product Dimensions	‎25.1 x 8.4 x 6.6 inches

5 Star

4 Star

3 Star

2 Star

1 Star

Напишите свой отзыв

Ваш адрес электронной почты не будет опубликован. Все обязательные поля помечены^*

Ваш рейтинг

Scritto da: SLady

Terrific!

This product is easy to work with. Covered my entire hot water heater. Good purchase.

Scritto da: Todd H.

Easier to install than expected

My gas water heater is in an unheated space, so I bought this kit to help with heat loss. This insulation kit was less expensive than other kits available, I assumed this would be because the wrap material was thinner. It was slightly thinner than other insulation wrap I previously used. I had some thicker wrap left from another project, enough to make a "disk" for the top of the heater, rather than fold over the edges of the top layer of the material per the instructions. This allowed me to used the 24" roll hight to make two wraps around the heater and finish with the bottom just above the air vents. The material itself went on easily. It stayed in place as I taped it on, making my cuts a around the various items as I went. This was a challenging installation as I only have access to the heater on two sides. The material was flexible enough to get around obstructions, but stayed in place once attached with the included tape. There seems to plenty of material to completely cover a standard size heater. I did run out of tape just as I finished, but did use extra tape around the earthquake strapping, so I believe there is also enough tape for most applications.

Scritto da: George E.

Quick And Easy

Way better fit (50Gal) than the usual blanket type…That an no Fiberglas issues! I like it…

Scritto da: D. R. Sauerzopf

Plenty of product to wrap a 40/50 gallon tank. No messy fiberglass. Installed on an electric heater

Just put in a new 40 gallon hot water heater. Used this wrap today. Had plenty of material to cover the tank with plenty of over wrap. The tape you get is fair. As long as everything is clean it should stick and hold. We shall see. I keep my basement around 72. Once I put the wrap on completely. I could feel heat coming off the top of the water heater. I did do the pizza cutting process for the top as recommended and I think some additional insulation would help on the top side since heat rises. All I used was scissors, utility knife, and a tape measure.

Scritto da: dokdmento

It’s better than the deteriorated insulation that I had but, the insulation is warm to the touch, so how good can it be? It was easy to install and not that expensive so…..

Scritto da: Aaron

Make sure you take the time to do it right (UPDATE: and buy different tape)

Break out your scissors and measuring tape, you are in for a crafting project. It does take some patience and precision to install correctly, but the end result is good. Allocate 1/2 hour for the installation. The product comes with ample insulation to cover a hot water heater (I had some left over). The silver tape roll that comes with the product was sticky enough to hold the insulation but wasn't quite long enough to do the full job. Overall, if you are the type who doesn’t mind spending the time to do something right, you’ll probably like this product. UPDATE: After being installed 2 weeks I notice that the silver tape is coming undone anywhere there is a corner or a fold. The tape just isn't made to last the test of time. I'll be looking to order some different tape to re-do the areas the tape is coming un-stuck.

Scritto da: Simon Elash

Keeps water heater warm

Could tell a difference immediately in as much as water heater kicking on. Takes a little time to install as you will need tape measure, some type of marker and scissors. Pretty easy to install just measure and take your time when taping and press tape to get good adhesion.

Scritto da: B. Callahan

Seems ok. A little thin

Another "get what you pay for" situation. It was easy enough to trim and tape onto the heater. But the material is thin and you can feel heat through it. It must be better than nothing, though. I hate fiberglass but I would get it if it was the only step up from this one.