Momentive RTV103 Силикон, однокомпонентный, черный, картридж 300 мл

Brand:Momentive

3.9/5

57.64

Однокомпонентный силиконовый герметик общего назначения, затвердевающий до прочного, прочного и эластичного силиконового каучука под воздействием атмосферной влаги при комнатной температуре. Продукт пастообразной консистенции стандартной прочности, который можно наносить на вертикальные и потолочные поверхности, где литьевые/самовыравнивающиеся герметики нецелесообразны. Обладает превосходными характеристиками при низких и высоких температурах от -75° до 400°f. может использоваться в приложениях, контактирующих с пищевыми продуктами, где применяются правила FDA, ссылка: Cds4319. признан UL в соответствии с файлом UL e-36952.

Соответствует военной спецификации mil-a-46106 и стандарту NSF 51, соответствует FDA 21 CFR 177.2600, соответствует требованиям USDA и имеет компоненты, признанные ul. Диапазон непрерывной работы составляет от -75 до +400 градусов по Фаренгейту (от -60 до +204 градусов по Цельсию), а диапазон кратковременной работы составляет от -75 до +500 градусов по Фаренгейту (от -60 до +260 градусов по Цельсию). Прилипает ко многим металлам, стеклу, керамике, силиконовой резине и некоторым жестким пластикам без использования грунтовки. Консистенция пасты позволяет наносить ее на вертикальные или потолочные поверхности. Однокомпонентный силиконовый герметик черного цвета пастообразной консистенции для заполнения и герметизации зазоров или трещин размером до 1/4 дюйма.
Country of Origin USA
Item model number RTV103-300ML
Manufacturer Momentive
Package Dimensions 11 x 1.5 x 0.94 inches; 10.41 Ounces

3.9

8 Review
5 Star
83
4 Star
17
3 Star
0
2 Star
0
1 Star
0

Напишите свой отзыв

Ваш адрес электронной почты не будет опубликован. Все обязательные поля помечены*

Scritto da: Wakawaka
Actual silicone is great, packaging no so much
So far I’m in for 7 tubes of this stuff and have had the same issue to varying degrees with all tubes. The plunger bypasses a ton of the silicone! Not only have I lost about 5-10$ worth of product every tube but my electric gun is a MESS. Yes I used a manual version too, and tried adding a fender washer to make sure I was supporting the entire plunger - same issue. I did cut my tips small and noticed that going slow reduced the loss but it shouldn’t be happening at all. Initially the directions fail to mention that you must puncture the inner seal after cutting tip. Not a big deal but threw me for a loop right off the bat because normally only cardboard adhesives have the seal and these tubes are plastic. Actual silicone is great quality, using it for fish tank stuff. I had success bonding acrylic to glass (over flow and sump building) and injecting it to reseal a stupid craigslist tank. One thing to note, if you’re using tape at the seam which you plan to remove while the silicone is still wet to get a clean line, you need to pull it off right after completing the seam. If you wait the typical 5 mins you’ll risk pulling the silicone OUT of the seam with the tape instead of just the excess that ran onto the tape.
Scritto da: ScottH
Sets up pretty quickly
It does grow a skin pretty quick, so you don't have heaps of time to get your bead looking the way you want. I found it stuck a little to the blue tape I was using as a mask. Not a big deal, but be prepared for it.
Scritto da: James daniels
This is what you want for fishtank's also, its black!
This is the best on the market for its application in fishtanks, its wayyyy better than silicone. Worth the expense. Just repaired a 3500 dollar fishtank i bought for 300 bucks with it.
Scritto da: I Buy Too Much
Works Like A Charm!
I chose this item due to the reviews regarding fish tanks. Had to reseal used bow front tank. Used frog tape to make perfect bead lines. Go slow by steady your caulk gun to get one continuous bead. Cut the caulk top to the size of bead you want to achieve. Do one pass with wet finger. Don't use a dry finger!!! Then do not touch it! Have wet paper towels ready as it can be messy. After drying I used a scraper to get off any random caulk. Do not scrap any part of aquarium side/bottom seal.If you made it messy, leave it. You do not want to break the cured seal. I waited until the vinegar smell was gone (about 40 hours as my tank was in garage) to rinse out and set up. Awesome product!
Scritto da: Brent Custer
Perfect
Caulking was perfect no hard spots. Great product and will buy again for sure
Scritto da: Bill
Used it to seal a 26 gallon tank worked excellent
Used it to seal a 26 gallon tank worked excellent
Scritto da: Tom Dehnert
Very strong aquarium safe
The best stuff period for redoing the inside of a fish tank
Scritto da: Mike jones
The best stuff around for Aquariums
Very strong, and very fast drying. Used it to repair damaged seals in a Waterbox rimless aquarium.

Сопутствующие товары

Откройте для себя нашу международную сеть

Мы отправляем в 28 стран, более 200 000 товаров. Будьте в курсе, подпишитесь на рассылку.

Array