0
0

Kopā:€ 0.00

Skatīt grozuIzrakstīties
LoginRegister
0

Kopā:€ 0.00

Skatīt grozuIzrakstīties
LoginRegister

CURT 56261 transportlīdzekļa pusē pielāgota 4-pin piekabes vadu instalācija, der atlasītai Toyota Sienna

Brand:CURT

3.7/5

€
114.07

Ja jūsu automašīna nav aprīkota ar vadiem piekabes vilkšanai, CURT pielāgota elektroinstalācija ir ideāls risinājums. Pielāgota vadu instalācija — saukta arī par T savienotāju — ir vienkārša, plug and play elektriska ierīce, kas tiek pievienota jūsu automašīnas elektrosistēmai un nodrošina standarta, universālu piekabes vadu savienojumu. Tas tiek darīts, izmantojot divus vai vairākus transportlīdzeklim raksturīgus, ar OEM saderīgus savienotājus, lai pievienotu aizmugurējo lukturu komplektam, novēršot nepieciešamību pēc griešanas, savienošanas un lodēšanas uzstādīšanas laikā. Pielāgotas vadu instalācijas ir pielāgotas transportlīdzekļiem, un, lai gan tās nav pieejamas visiem transportlīdzekļiem, tās piedāvā vienu no ātrākajiem, vienkāršākajiem un drošākajiem veidiem, kā savienot transportlīdzekli vilkšanai. Šajā konkrētajā spraudsavienojuma instalācijā ir četrvirzienu plakana savienotāja ligzda, un tā ir izstrādāta kā pielāgota vadu instalācija, lai tā būtu piemērota noteiktiem Toyota Sienna gadiem (lai pārbaudītu sava transportlīdzekļa saderību, skatiet informāciju par lietojumprogrammu). Tam ir visi nepieciešamie vadu komponenti, lai izveidotu uzticamu piekabes vadu savienojumu, kā arī putekļu vāks, lai savienotājs būtu tīrs, kad to neizmanto. Jums ir prātā priekšstats par savu nākamo galamērķi — varbūt tā ir laiva, kas nolaižas jūsu iecienītākajā makšķerēšanas vietā, varbūt tas ir kempings, no kura paveras skats uz kādu no dabas šedevriem, vai varbūt tā ir nākamā lielā darba vieta. Tomēr šī attēla pārvēršana realitātē prasa vairāk nekā tikai sapņošanu. Tas prasa stabilu savienojumu un pareizo enerģijas daudzumu. CURT pielāgota elektroinstalācija ir izgatavota, izmantojot dažas no vismodernākajām tehnoloģijām nozarē, un ir paredzētas vieglai uzstādīšanai, nodrošinot ilgstošu elektrisko savienojumu jūsu sakabes āķa uzstādīšanai.

Summa
Pievienot grozamPērc tagad

EAN: 0612314562619

Kategorijas Automobiļu nozare, Interjera piederumi, Tilpnes un vinčas, Kravas bagāžnieku stiprinājumi Aksesuāri, Kārtu elektroinstalācija,

PUTEKĻU KĀRTA. Lai veicinātu ilgstošu lietošanu un izturību pret laikapstākļiem, šai 4-polu piekabes apgaismojuma vadu instalācijai ir gumijas putekļu pārsegs. Tas viegli pieguļ četrvirzienu plakanajam savienotājam, kad tas netiek lietots, aizsargājot to pret āra, ārējiem elementiem un iekšējo koroziju. UZTICAMA JAUDA. Šī četrvirzienu piekabes vadu instalācija ir veidota, izmantojot virsmas montāžas tehnoloģiju. Šāda veida shēmas rada mazāk siltuma, optimālu gaismas intensitāti un izturīgu veiktspēju. TRANSPORTLĪDZEKĻIEM. Šī pēcpārdošanas transportlīdzekļa piekabes vadu instalācija ir paredzēta noteiktiem Toyota Sienna gadiem. Tas nodrošina vienkāršāko iespējamo uzstādīšanu un visuzticamāko vadu savienojumu. Pagriezienu un bremžu ķēdes: 3 ampēri. STANDARTA SAVIENOTĀJS. Šo iespraudamo 4 plakanu piekabes vadu var izmantot, lai savienotu piekabes aizmugurējos lukturus, bremžu signālugunis un pagrieziena rādītājus. Četrvirzienu piekabes gaismas vadi ir populāri visdažādākajās piekabēs, pievienojot daudzpusīgas vilkšanas iespējas jūsu transportlīdzeklim. VIEGLI UZSTĀDĪT. Nekādas griešanas! Nav savienojuma! Šis piekabes vadu komplekts tiek pieslēgts esošajiem jūsu transportlīdzekļa rūpnīcas vadiem un aprīkots ar standarta aizmugurējo 4 kontaktu piekabes vadu savienotāju piekabes vai piederumu pievienošanai un vilkšanai. Piemērošanas veids: Transportlīdzeklim.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.6 4.6 out of 5 stars 302 ratings 4.6 out of 5 stars
Exterior ‎Painted
Is Discontinued By Manufacturer ‎No
Item model number ‎56261
Item Weight 1.6 Pounds
Item Weight ‎1.6 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎56261
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎BKDK56261

3.7

11 Review
5 Star
78
4 Star
13
3 Star
4
2 Star
2
1 Star
3

Uzrakstiet savu atsauksmi

Jūsu e-pasts netiks publicēts. Visi obligātie lauki ir atzīmēti ar*

Scritto da: Amazon Customer
Plug and play, easy hookup
We like the Curt plug and play products for Toyota vehicles. This is the third one we have tried, and they work great. Easy installation. You do usually have to run a wire to the battery, so be prepared to get a little bit dirty. (On the Sienna van, we stole power from the little light in the back right side, so didn’t have to get under the car)
Scritto da: Amazon Customer
Works as advertised.
A company installed the first 2 of these in my vehicle, and they would only last 2 years each. Now i know why. The power wire was touching the exhaust, and the module was spliced in with those blue t clips and hanging from the left rear taillight and dangling between bumper plastic and frame. Not enough wire to get to module from top or bottom. Grrrrrr. Some advice, get this and do it yourself. Mount it on the inside of the vehicle to keep it sheltered from rain, and so it doesn’t bang around with every start or stop. Is not hard to install at all.
Scritto da: A. Langer
Fit was good, instructions are lacking
This fit our 2015 Toyota Sienna just fine. As others have said, I was expecting the difficulty in getting the wire under the van up to the battery. I jacked up the rear of the van to help some and use a fish tape in some spots. I had no idea where to mount the black box behind the paneling. When I decided on a place, the the peel and stick pad fell off immediately and had no stick. I don't know if it was because it was only 40 deg, but it felt more like it was old adhesive. So I zip-tied it to a bracket there. Hopefully it doesn't bang around too much. Also, the red fuse holder/wire provided was not a very flexible plastic and I felt like it was going to break just closing the cap. Directions were ok, but they were just tiny black and white images and I could barely see what was going on. This is 2022 I expect a lot more. I guess that's why we all watch a video online first, but the instructions should hold their own.
Scritto da: Amazon Customer
Works well, but read this before installing
Installed in Toyota Sienna 2015. Overall, good kit but things you should know... 1) ***Install control unit on passenger side of car*** There's more room, there's a car jack compartment to store the cable when not being used, and you can use electricity from the right outlet (see next point). This means running the green wire to the left blinker and yellow wire to the right blinker. This will later require you to cut the green/yellow wires coming out of the control unit and switch them or your blinkers will be backwards. Not hard to do with simpler wire couplers. 2) If your vehicle has a 12V outlet (cigarette style) in the passenger rear next to the car jack compartment, then you can connect the black/white to that instead of running a wire all the way to the front of the vehicle. Way easier!!! You can either tap into them using a simple T-Tap, or order a male 12V plug, attach the wires to that, and "plug it in" when you need it. I went with a T-Tap since it's easier. Don't forget to install the fuse that comes with the kit on the black wire. Note: This is the 12V cigarette style outlet, not the 120V prong outlet. Your car may have both. Don't use the wrong one! 3) The instructions are useless. Luckily, lots of videos online. The only wires I cut were on the unit to switch yellow/green after it comes out of device. Pretty easy install overall.
Scritto da: Mike Partridge
Installation videos help a lot (2015 Sienna)
Connecting the wiring into the brake lights wasn't too bad. Watching a couple of installation videos helped a lot. I connected the bulk of the wiring to the driver side like it was designed for. I don't have a good way to get under the vehicle to run the wire, so I ran it under the trim on the driver's side. I didn't see a video that showed how to get the wire through the firewall to the engine but I read elsewhere that someone got it through a grommet. Here's how I did it: I found where the bulk of the wiring from the passenger compartment goes through the firewall (photo 1). There are seams in the insulation, so I peeled it back to the right to expose the grommet and noticed a round opening on one side (photo 2). I pushed a narrow screwdriver through and found that the opening leads to an otherwise unused protrusion on the engine side of the grommet (photo 3). I cut an X in the end of the protrusion, and because the wire is fairly stiff, was able to feed it through the opening in the grommet. Feeding it through the rest of the way to the battery was no trouble.
Scritto da: Kindle Customer
Great module! Check your year and model!
+ Works great in 2014 Toyota Sienna LE after difficult install. - Triple check your year and model - Use VIN number at toyota.com. + NOW I see Amazon had SE in "my garage" instead of LE. My fault for not checking that. + CURT's web site agrees the 2014 SE and 2014 LE use different connectors. + I also see in Q & A someone had a 2015 LE with different connectors than 2014 LE. + The power line with fuse that Curt included with this was just long enough and Curt included plenty of tie wraps to help. It reaches front battery, under van, up existing grommet hole into trunk, and over to left stop light area where module can be placed. This part of install was as easy as could be, though best done with a full car lift and a fair amount of patience. - You may be tempted to tap into the 12V access point in back for power. Don't forget that shares a fuse with your GPS, phone chargers, and any add-in DVD players you have plugged in. It may work on your trailer or with LED lights, then if you borrow a U-Haul with extra marker lights, running lights, and hit the brakes you could blow that little fuse. I decided to give the lights their own dedicated line as recommended. + Great quality! + Solid unit, well sealed, durable cables. + Much smaller than the space available for installation.
Scritto da: howard
good diy trailer wiring conversion
easy diy hook up of trailer wiring to Toyota. converts to 3 wire and does it in a simple and not fuss, cut, solder way. comes with all the required materials to get the job done quickly although you should not expect it to take 20 minutes but rather a couple of hours depending to the number of pieces of interior trim you need to remove to get access. has worked well for over a year and expect that it will continue to do so. a little pricey but I guess that is the price for simplicity
Scritto da: Wes
Hard to install power line
Worked great on our 2015 Toyota Sienna. They expect you to run the power line all the way under the car to the battery. we have AWD, so I could not find a spot to run the wire, and it seemed short. I ended up jumping power from the cigarette lighter in the back, which only has power when the car is in acc or is on, but it was better than nothing.
Scritto da: Mike Carriere
Sienna wiring harness
The wiring harness fit well and installed quickly.
Scritto da: Amazon Customer
Very happy with it
It fit very nicely and everything works great,
Scritto da: Hai Lan
perfect quality
still in good condition after very long time use

Saistītie produkti

hot
CURT 55326 transportlīdzekļa pusē pielāgota 4 kontaktu piekabes vadu instalācija, der atsevišķiem Ford Crown Victoria, Ford Mustang, Mercury Grand Marquis, melna
3.3/5

€ 68.63

CURT 55326 transportlīdzekļa pusē pielāgota 4 kontaktu piekabes vadu instalācija, der atsevišķiem Ford Crown Victoria, Ford Mustang, Mercury Grand Marquis, melna
3.3/5

€ 68.63

hot
CURT 60601 OEM Puck System 2–5/16 collu zoss kakla bumba, der atsevišķām kravas automašīnām, 30 000 mārciņas
3.6/5

€ 420.27

CURT 60601 OEM Puck System 2–5/16 collu zoss kakla bumba, der atsevišķām kravas automašīnām, 30 000 mārciņas
3.6/5

€ 420.27

hot
CURT 55486 transportlīdzekļa pusē pielāgota 4 kontaktu piekabes vadu instalācija, der atlasītajam Toyota RAV4
3.6/5

€ 81.06

CURT 55486 transportlīdzekļa pusē pielāgota 4 kontaktu piekabes vadu instalācija, der atlasītajam Toyota RAV4
3.6/5

€ 81.06

hot
Hopkins Towing Solutions 52027 7 ceļu tapas tipa piekabes gala savienotājs ar kabeļa aizsargu
3.9/5

€ 46.49

Hopkins Towing Solutions 52027 7 ceļu tapas tipa piekabes gala savienotājs ar kabeļa aizsargu
3.9/5

€ 46.49

hot
CURT 51446 ātrā spraudņa bremžu kontrollera vadu instalācija, saderīga ar Select Chrysler Pacifica, Dodge Durango ar piekabes paketi, Jeep Grand Cherokee
3.8/5

€ 48.60

CURT 51446 ātrā spraudņa bremžu kontrollera vadu instalācija, saderīga ar Select Chrysler Pacifica, Dodge Durango ar piekabes paketi, Jeep Grand Cherokee
3.8/5

€ 48.60

hot
CURT 58545 transportlīdzekļa puses 5-pin plakanā piekabes vadu instalācija
3/5

€ 31.31

CURT 58545 transportlīdzekļa puses 5-pin plakanā piekabes vadu instalācija
3/5

€ 31.31

hot
GM piederumi 12496599 7 kontaktu apaļš līdz 4 kontaktu plakanai piekabes vadu instalācijas adapteris
3.6/5

€ 50.26

GM piederumi 12496599 7 kontaktu apaļš līdz 4 kontaktu plakanai piekabes vadu instalācijas adapteris
3.6/5

€ 50.26

hot
CURT 57271 5 pēdu 7 virzienu RV lāpstiņas, no sāniem līdz 4 virzienu plakanajai piekabes vadu adaptera pagarinājuma instalācija, melna
3.8/5

€ 60.17

CURT 57271 5 pēdu 7 virzienu RV lāpstiņas, no sāniem līdz 4 virzienu plakanajai piekabes vadu adaptera pagarinājuma instalācija, melna
3.8/5

€ 60.17

Atklājiet mūsu starptautisko tīklu

Mēs piegādājam uz 28 valstīm, vairāk nekā 200 000 produktu. Esiet informēts, abonējiet biļetenu.

Array

Kopā:€ 0.00

Skatīt grozuIzrakstīties

Kategorijas

Visas kategorijas
Izvēlne Kategorijas Netālu Ratiņi

Menu