Eagle Tool US ET18721 uzstādītāja urbja kāts, lietots ar maināmām slēdža uzgaļu galviņām, 3/16 collu x 21 collu, ražots ASV, 3/16 collas 21 colla.

Name: Eagle Tool US ET18721 uzstādītāja urbja kāts, lietots ar maināmām slēdža uzgaļu galviņām, 3/16 collu x 21 collu, ražots ASV, 3/16 collas 21 colla.
Brand: Eagle Tool US
SKU: 0850078004116
Price: 44.34 EUR
Availability: InStock

Brand:Eagle Tool US

3.9/5

€
44.34

Eagle Tool individuāla izmēra, elastīgi atsperu tērauda kāti. Elastīgie atsperu tērauda kāti ir aprīkoti ar zivju izmitināšanas caurumiem, trim plakaniem, neslīdošiem patronas rokturiem un slīpētu neslīdošu iegriezumu maināmajai galvai. Stiepļu zvejas caurums patronas galā. Kāts mēra 3/16 collu diametru un 21 collu garumu.

Summa

Pievienot grozam Pērc tagad

EAN: 0850078004116

Kategorijas instrumenti un mājokļa labiekārtošana, Elektroinstrumenti un rokas darbarīki, Elektroinstrumentu daļas un piederumi, Elektrourbju daļas un piederumi, urbji Uzgaļi, Instalatoru urbji,

Maināms regulēšanas skrūves un sešstūra uzgriežņu atslēgas komplekts ETAKIT2. Stiepļu zvejas caurums patronas galā. Neslīdošs plakans (urbšanas gals) un neslīdošs trīs plakans rokturis (patronas gals). Elastīgs atsperu tērauda kāts. Izmantošanai ar galviņām ETS375, ETS562, ETH375, ETM375 un paplašinājuma adapteri ETHXKIT187.

Brand	Eagle Tool US
Country of Origin	USA
Cutting Angle String	135 Degrees
Domestic Shipping	Item can be shipped within U.S.
Finish Type	Black Oxide
International Shipping	This item can be shipped to select countries outside of the U.S.
Item model number	ET18721
Manufacturer	Eagle Tool US
Material	Alloy Steel
Shank Type	Round

5 Star

4 Star

3 Star

2 Star

1 Star

Uzrakstiet savu atsauksmi

Jūsu e-pasts netiks publicēts. Visi obligātie lauki ir atzīmēti ar^*

Jūsu vērtējums

Scritto da: Amazon Customer

Much better than single piece design

I have a business that provides low-voltage installation services. I greatly prefer an interchangeable setup like this over single piece (bit plus shaft design). With the single piece once you dull the bit you have to replace the entire thing (at $30-50 a pop), not to mention you end up needing 4-8 different bits to accommodate different drill bit sizes and lengths. It is easy to attach a new bit and the lip design helps prevent the bit from spinning loosely. The reason for 4 stars is because you have to really make sure to get the screws tight on this otherwise you end up with a bit stuck inside the wall. FYI the 90 degrees is for the entire length of the rod, dont expect to make a 1" hole and bend this at a sharp 90 degree angle. Also the larger the drill bit the slower you should go with your drill. If you try to push a 3/4" bit through a double 2x4 header at max speed you will likely break the rod before you drill through.

Scritto da: Jarrod Major

A decent size for those hard-to-reach places

Pretty simple tool, not much to say, it does the job. 1/4" shank is very rigid. Like the convenient hole on the drill side for wire pulls.