CURT 31075 2 collu priekšējais uztvērēja sakabe, izvēlieties Toyota Tacoma

Brand:CURT

3.6/5

494.96

CURT priekšējā piekabes sakabe ļauj izmantot automašīnas priekšējo daļu dažādiem vilkšanas darbiem. Tos var izmantot, lai uzstādītu vinču, sniega tīrītāju, vairākus vilkšanas piederumus, un tos var izmantot pat dažām piekabēm. Ja vieta ir ierobežota, kravas nesēja noturēšanai parasti izmanto priekšējo piekabes sakabi, tādējādi atbrīvojot vietu transportlīdzekļa iekšpusē papildu kravai un padarot aizmugurējo uztvērēju pieejamu piekabes vilkšanai. Pie laivas rampas jūsu laivas piekabi var uzkabināt līdz priekšējai uztvērēja sakabei, nodrošinot labāku piekabes vadību, kad to nolaižat. Daži citi piederumi, ko var izmantot ar priekšējo sakabes āķi, ir CURT vinčas stiprinājums, pakāpiena paliktnis, numura zīmes turētājs, rezerves riepas stiprinājums, buksēšanas vairogs un sakabes āķi. Visas CURT priekšējās piekabes sakabes nodrošina noderīgu uztvērēja cauruli, lai pieņemtu 2 x 2 kātu, un tos parasti izmanto kravas automašīnās, furgonos un SUV. Šī priekšējā piekabes sakabe ir paredzēta 3500 mārciņām. GTW un 350 mārciņas. TW. Tam ir arī taisnas līnijas vilkšanas reitings 9000 mārciņas. Tas ir paredzēts kā pielāgota piekabes sakabe noteiktiem Toyota Tacoma gadiem (lai pārbaudītu automašīnas saderību, skatiet informāciju par lietojumprogrammu). Tam ir visa nepieciešamā aparatūra pilnīgai instalēšanai, un tam ir ierobežota mūža garantija.

VIEGLA UZSTĀDĪŠANA. Šis priekšējais sakabes āķis ir izstrādāts ar transportlīdzeklim raksturīgu dizainu, lai tas atbilstu atsevišķiem Toyota Tacoma modeļiem. KOROZIJAS IZTURĪGS. Lai nodrošinātu izcilu aizsardzību pret rūsu, šķembām un UV bojājumiem, šī priekšējā uzkare ir pārklāta ar divslāņu rūsu noturīgu A veida pārklājumu, kas pārklāj uzkabi no iekšpuses un ārpuses, un ar īpaši izturīgu melnu pulvera pārklājumu. PĀRBAUDĒTA BŪVE. Šī priekšējā stiprinājuma uzkare ir pilnībā pārbaudīta jūsu drošībai mūsu Detroitas inženiertehniskajā iestādē. Mēs pārbaudām mūsu priekšējās piekabes sakabes konstrukcijas saskaņā ar SAE J684 specifikācijām. UZTICAMS SPĒKS. Šī priekšējā uzkare ir paredzēta 3500 mārciņām. GTW un 350 mārciņas. mēles svars. Tas ir arī novērtēts uz 9000 mārciņām. taisnas līnijas vilkšanas jauda vilkšanai un vinčai (ierobežota līdz viszemākā nominālā vilkšanas sastāvdaļai). DAUDZUMS UZTVERTĀJS. Pievienojiet noderīgu sakabes uztvērēju sava transportlīdzekļa priekšgalam ar šo priekšējā stiprinājuma uztvērēja uztvērēju. Standarta 2 collu uztvērējs ļauj piestiprināt sniega tīrītāju, kravas bagāžnieku, velosipēdu bagāžnieku, sakabes āķi, vinčas stiprinājumu vai citu vilkšanas piederumu.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.6 4.6 out of 5 stars 153 ratings 4.6 out of 5 stars
Exterior ‎Gloss Black Powder Coat
Finish Type GLOSS BLACK POWDER COAT
Item model number ‎31075
Item Weight ‎26.6 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎31075
Material Carbon Steel
Model ‎Front Mount Hitch
OEM Part Number ‎31075
Product Dimensions ‎44 x 15 x 8 inches
Vehicle Service Type Marine-Personal-Craft, Van, Sport-Utility-Vehicles, Truck, Trailer

3.6

10 Review
5 Star
81
4 Star
10
3 Star
2
2 Star
1
1 Star
5

Uzrakstiet savu atsauksmi

Jūsu e-pasts netiks publicēts. Visi obligātie lauki ir atzīmēti ar*

Scritto da: RAzer
Perfect fit
Installed the hitch to mount a snow plow. It was a perfect fit for my Tacoma as it was advertised. Th installation instructions can be more specific and detailed; which would make the installation process much easier.
Scritto da: Cortney B.
Best front receiver on the market.
This this is solid I’m just not a fan of altering factory plastic it’s just a pain to get a nice finish on it. Other than that if your looking for a front receiver for a Toyota Tacoma this is #1 in my opinion.
Scritto da: David Sherritze
Nice quality bracelet
Nice product a little difficult to trim existing facia. But very good product.
Scritto da: Eugene
Excellent front receiver hitch
Hitch arrived in excellent condition. Took about 15 or twenty minutes to install. I saw many that installed hitch left off front lower fascia. There are instructions about cutting the fascia so it will fit around the hitch. I didn’t like the large gaps that would be left so I scribed my fascia to the hitch for a more custom fit. That took the rest of the day. All together, very pleased with the hitch.
Scritto da: makamai
good quality
easy install. solid.
Scritto da: Kindle Customer
Fits perfectly with required modifications
I installed this on a 2017 Toyota Pro. The instructions, which suck, state the skid plate needs to be "trimmed", but fail to explain what part of the plate needs trimmed or how much. After removing the tow hook on the passenger side and the bolt on the opposite side (driver's side) and then holding the hitch in place, it is fairly easy to determine how much of the skid plate to trim. I used a cut-off grinding wheel and cut approximately 1 and 1/2 inches off the very front of the plate. I trimmed the plate without removing it from the vehicle. Once trimmed, the hitch was easy to install. Like other complaints, it is nearly impossible to torque the top bolts; I used a box end wrench and know that I met or exceeded the torque requirements. Note that there is no air dam on a Toyota Pro, so that installation step (trimming the air dam) is not required. I installed this hitch so I could mount a receiver winch; the ground clearance is not effected by installation of the hitch, however I did purchase a hitch extender (about 20 bucks) so the winch was not resting against the license plate holder. Considering the cost of a winch bumper ($1500) and the permanent modification of the vehicle body (cutting a part of the fenders off), this is an excellent alternative. I would definitely purchase this again, or recommend it to someone who doesn't want to pay $400-$500 to modify the pickup for a winch bumper.
Scritto da: E. Seale
Great product, fit like a dream
I've got a 2017 Tacoma TRD Off-Road, and this unit installed without any issues. It's a high-quality product, and is beautifully finished (so, should handle road crud without problems). Extra bonus points -- it's built in the U.S.! It's so refreshing to be able to buy an affordably priced high-quality item that's domestically produced. I bought a similar unit for an earlier Tacoma, and got years of trouble-free service from it -- so I expect the same with this one. Some installation tips: 1) The installation instructions have good diagrams, but dark photos -- I'd recommend a quick online search to watch install videos before you start to work. 2) The mount is attached to your truck with two bolts on each end. I'd recommend you install the top bolt first (the one supplied with the unit); this way, you can leave the "cross beam insert" out while dealing with the top bolt. This gives you access to the back of the bolt, particularly handy if the thing gets loose (after you remove its "fish wire") and drops into the cross beam. This probably sounds like gibberish before you buy the unit, but it'll make sense when you have the installation instructions and parts kit in front of you. 2) The "fish wires" are a great way to get the top bolts and their spacers lined up with the appropriate holes. But once you take a bolt's fish wire off, it's free to fall back into the frame / cross beam (see tip 2, above). Fortunately there's a small hole behind this area in the frame -- I found it helped to hold the bolt in place with a skinny socket driver (something likethis ), at least until I got the respective nut started on the bolt (i.e., use the socket driver to push the bolt toward the nut).
Scritto da: C. J. Ervin
Curt quality for frount mount gear
I always buy Curt product for towing related items. Solid assembly, quality materials, competitive price and a great fit. This is a great front mount receiver for a 3rd gen Tacoma. It took 20 minutes to install. The instructions say that you will need to trim the skid plate for the TRD Off Road model, but as you can see in the images, you do not as there is ample clearance between the skid plate and the receiver.
Scritto da: JC
Excellent poduct
Fits 2017 Tacoma perfectly, installed in 35mins by Toyota mechanic (first time install). So I didn't have to get cold and dirty cost me $65 to get it install at dealership ( in Canada). match truck perfectly. Highly recomend. only bad note it came slightly damaged in shipping and seller never got back to me. for this it lose a star.
Scritto da: Robert Virtue
Good hitch for the money
Arrived in a box that was completely destroyed by shipping monkeys. However they could not destroy the hitch. Well made, piece of metal. Install was straight forward on my 2108 Toyota Tacoma Off Road. I took my time and it took me about an hour. Would buy again.

Saistītie produkti

Atklājiet mūsu starptautisko tīklu

Mēs piegādājam uz 28 valstīm, vairāk nekā 200 000 produktu. Esiet informēts, abonējiet biļetenu.

Array